We also know how well they respond to boost, so the obvious question, then, is how well do they respond to both? While the answer may seem obvious, there is much more to it. Suppose you upgrade your LS engine with a performance camshaft, aftermarket cylinder heads, or an intake manifold—or better yet: all three like we did to our test engine. Will the power gains offered on the normally aspirated engine carry over once you add boost? What if the camshaft is tailored more toward forced induction, or not? The same could be asked of the intake or cylinder heads. We didn’t know the answers to these questions going into this project, but we sure knew how to find out.
While the questions were simple enough, finding the answers required no less than four different engine configurations. The test would start with a stock (actually near stock) 5.3L which we ran first in naturally aspirated trim, then again with a single turbo system. After running those two configurations, we then replaced the stock cylinder heads, camshaft, and intake manifold with aftermarket versions, then ran the tests again—both naturally aspirated and with the same turbo system used on the stock engine. In doing so, we could compare the power gains offered on both the naturally-aspirated combo and on the turbocharged version.
To start, we used a 5.3L engine built by David Freiburger for an episode of Engine Masters on MotorTrend. Equipped with forged rods and pistons from Wiseco, we reconfigured it with a stock LM7 cam, the original 862 heads, and an early 5.3L truck intake and stock throttle body, a set of 120-pound Holley injectors and 1 7/8-inch long tube Hooker headers. Dialing in the air/fuel ratio and timing curve was a Holley HP management system. Run in anger with the stock heads, cam, and intake, the 5.3L produced 333 hp at 5,200 rpm and 359 lb-ft of torque at 4,400 pm. Now it was time for some boost!
This story is from the April 2020 edition of Hot Rod.
Start your 7-day Magzter GOLD free trial to access thousands of curated premium stories, and 8,500+ magazines and newspapers.
Already a subscriber ? Sign In
This story is from the April 2020 edition of Hot Rod.
Start your 7-day Magzter GOLD free trial to access thousands of curated premium stories, and 8,500+ magazines and newspapers.
Already a subscriber? Sign In
Making Connections
Project T-top Coupe: We install a Terminator X Max for big power.
LET IT BREATHE!
Project X’s new ZZ632 big-block needed to breathe, and this do-ityourself stainless exhaust kit was just the ticket to make it happen.
TUNING OPTIMIZED
VARIABLES WITHIN FUEL-INJECTOR CONSTRUCTION CAN LEAD TO POOR ENGINE OPERATION. HERE'S HOW TO TUNE YOUR FUEL INJECTORS.
Re-Flange It!
We check out the fab skills needed to run a flat hood on a 1970 Mustang with a very unique and too-tall engine.
THE TRIBUTE FOR THE WIN
Ron Capps wins the NHRA U.S. Nationals driving a Don Prudhomme-Hot Wheels tribute Funny Car.
So Close
Following a nearly flawless performance, a pít lane penalty kept the C8.R off the top of the podium in the IMSA Sportscar Weekend.
A RADICAL SHIFT
When you're a teenager and the police know you by name, it's not usually because of your volunteer work or class-topping GPA. Not at all. That was especially true for Jeff Kainz when he was behind the wheel of his 1975 Camaro. In the '80s, while cruising his hometown in North Dakota, his buddies with police scanners often heard the police tell one another: \"Kainz is out on Main Street.\"
WILD MASH-UP
Built to long-haul the 2023 HOT ROD Power Tour, this 1984 Monte Carlo’s facade hides a performance secret!
6 TIMER!
Tom Bailey captures his 6th HOT ROD Drag Week Unlimited/Overall title with his Sick Seconds 1.0 Camaro.
JIM MCFARLAND'S INFLUENCE WENT WAY BEYOND HOT ROD MAGAZINE.
Jim McFarland, the multitalented, multifaceted Texan who enjoyed several careers in the automotive performance industry, passed away in October 2023 at the age of 88.